热水器常见故障维修和排除方法(T

热水器常见故障维修和排除方法（Troubleshooting and

troubleshooting of water heater）

Troubleshooting and troubleshooting of water heater

Common faults and solving methods of gas water heater

Fault phenomenon, cause analysis, treatment method

The air in the newly installed pipe is not discharged, the

ignition time is prolonged, and the air in the pipe is

discharged

The gas pressure is too large or too small, replace the pressure

reducing valve or check the gas pipe whether there is bending

No power check battery or power outlet

The water supply valve is not opened or is not fully opened,

check the water supply valve and turn it on completely

The water pressure is insufficient, try again when the water

pressure is enough

Do not contact the manufacturer with gas

The gas pressure is too large or too small, adjust the pressure

of the reducing valve or replace the pressure reducing valve

properly

Use a middle fire to extinguish a pressure relief valve or a line block, replace the pressure relief valve, or check the gas

line for bending

The water pressure changes or is too low. Try again when the

water pressure is high enough

Hot water is too hot, water pressure is low, install booster

pump

Hot water is not heated, pressure reducing valve or pipeline

is blocked. Replace pressure reducing valve and check air way

valve

The inlet temperature is low, the gas supply is increased, and

the cooling water supply is reduced

Open the hot water faucet can not immediately produce hot water,

from the water heater to the tap is a distance, because the water

residue in the pipe, it takes a little time, is a normal

phenomenon

Exhaust steam from the exhaust cylinder, because the exhaust

gas contains a lot of water vapor, in case of cold air outside,

you can see the white gas is a normal phenomenon

When the above trouble cannot be ruled out, please contact

Sakura head office or local branch office.

Common faults and solutions of electric water heater

Fault phenomenon, cause analysis, treatment method The hot water outlet does not drain the hot plug. The reset

button does not press the reset button

No power supply, power supply

The thermostat is at the lowest temperature and the thermostat

is at the highest temperature

The heating time is not long enough to wait for heating

Tap water is not available until the water is supplied

The water pressure is too low to be used until the water pressure

rises

The tap water inlet valve is not opened, and the inlet valve

is opened

During heating, the safety valve drips and the water expands

when heated, and a diversion pipe is added to the water

The hot water is white and cloudy. The air dissolved in hot water

will disappear naturally

Beat the body to show "leakage" leakage, and alarm leakage

protection device, sensitive to power, do not beat the machine,

after false positives, cut off the power supply, RE activated

The body shows "water shortage", the water tank is dry, the

container is filled with water and it is restarted When the above trouble cannot be ruled out, please contact

Sakura head office or local branch office.

For the first time, it is necessary to fill the water heater

before allowing the power to be switched on.

Common troubles and solving methods of gas cooker

Fault phenomenon, cause analysis, treatment method

No fire

The air in the newly installed pipe is not discharged, the

ignition time is prolonged, and the air in the pipe is

discharged

Ignition electrode; dirty cleaning; ignition electrode

The gas pressure is too large or too small to replace the

pressure reducing valve or check the gas pipe for bending

No battery or loose, properly installed, battery or plugged in

Burning peculiar smell

Oil or debris is cleaned or removed on the burner

Fire while burning

The gas pressure is high, adjust the pressure of the pressure reducing valve or replace the pressure reducing valve properly

Gas type is incorrect. Contact the manufacturer

The bottom of the pan blackened when it was burning

Bottom gas (liquefied gas bottle) to replace the gas bottle of

Xingang

The furnace holder is not properly placed

There is a sound at the time of the fire

The tooth cover is not covered well

Correct placement

The ignition electrode is dirty

Clean ignition electrode

.

Common troubles and solutions of range hood

Fault phenomenon, fault reason, treatment method

The light is not on, the motor switch bulb is out of contact

with the lamp holder, replace the bulb or tighten

Bulb burned out, replaced Not light the motor does not turn to check whether electricity

sockets used shidianbi check whether electricity sockets

Motor temperature over 130 degrees automatically stop

protection, natural cooling can be used normally

Suction is not enough, the body is too far away from the furnace

surface, lower the height from the new installation

There are too many doors and windows around the body, the air

convection is too large, and the doors and windows are closed

to reduce the convection wind

Yuba, common troubles and Solutions

Fault phenomenon, fault reason, treatment method

The lamp is not lighted, the lamp is broken, and the lamp is

changed

The illuminating lamp is not screwed and tightened

The heating lamp is not lighted, the heating bulb is bad, and

the heating bulb is changed

The heating lamp is not screwed in place, and the heating lamp

is screwed tightly

Common troubles and solutions of water tap

Fault phenomenon, fault reason, treatment method

No water or water, small bubbles, plug in the head, remove

debris

Sprinkler water outlet plug

After the water supply or the water pressure is low, the booster

pump is reset or installed after the water supply

Sink common faults and Solutions

Fault phenomenon, fault reason, treatment method

The water pump is leaking, and the rubber ring is broken or

damaged, and the rubber ring is mounted or replaced

The center screw of the launching device is not tightened. Screw

down the center screw

Overflow, overflow, rubber cushion, leakage or rough mounting

or flat rubber pad

Screw release screw

Drain water seepage part, sealing ring leakage or nut loose,

install sealing ring or tighten nut

Drainage pipe whether horizontal or vertical adjustment

installation position to ensure horizontal or vertical

Slow drainage, debris in the pipe plug, find the blockage,

cleaning debris

Luoyang Hongqi home appliance repair center was founded in 2002,

in more than 10 years of development, has now become a number

of home appliances brand after-sales service sentinel. With the

number of home appliance enterprises combination, training a

group of excellent technology, good service quality and

maintenance personnel, they have a long time in the customer

service service and maintenance work, the door can do fast, high

efficiency, good service, fast maintenance, saving valuable

time for the majority of users!

In the long-term maintenance practice, worked out a set of

scientific and standardized methods of maintenance, repair of

the invention made lots of special tools, large appliances are

not out of the door, you can at home in a fast and good

maintenance, parts used by the company are directly from

factory orders, although the cost increased, but the

maintenance of the product safety and durability, the company's

solemn commitment to the maintenance of the appliance warranty

for 1 to 3 years, our slogan, repair the rest assured -- with

the peace of mind, comfortable consumption.

1: telephone contact company customer service, explain your

electrical fault, leave your contact information.

2: we will contact you in the shortest possible time, arrange

the master to serve you.

3: home maintenance, troubleshooting. 4: issued warranty proof, enter the after-sales service repair

period.

Luoyang red flag maintenance is your most loyal friend, is

willing to provide you with the best quality service, the most

reasonable charges. Contact information