2023年12月20日发(作者：关维晓)
Title:
TP – 09001 – US
01
Test Protocol
Version:
Report #:
Subject:
US report checklist - Children
Approved by: Stephan Pesch
Test Requirement Sample Result/Remark
Chemical Requirement
All accessible surface coatings shall not contain
CPSIA Total lead content in surface
lead in excess of 0.009% (90ppm) of the weight
coatings
of the total content of paint or surface coating.
CPSIA Total lead content in
substrate material
All accessible substrates on items intended for
children ages 12 and under shall not contain lead
in excess of 0.03% (300 ppm) of the weight of
the total content.
Actual testing would be conducted on all
accessible plastics materials (including natural
and synthetic rubber), plasticizer print, scrapable
surface coatings, decals, polymeric coated
materials (unscrapable), adhesives and sealants
(exclude adhesive for stickers), toy nail polish,
reusable packaging, electrical plug or cables and
inaccessible plastic sheath of electrical wires
Vendor shall be responsible for the compliance
of all other accessible materials and inaccessible
materials that become accessible after
competing mechanical hazards testing.
Children’s toys and childcare articles in the as
received state shall not contain concentrations of
more than 0.1% BBP, DBP or DEHP, individually.
Children’s toys that can be placed in the mouth
or childcare articles in the as received state shall
not contain concentrations of more than 0.1%
DINP, DIDP or DnOP, individually.
The metal content of the soluble material should
not exceeds the levels by weight (mg/kg) of the
contained solid including pigments, film solids
and driers [Antimony (Sb) 60, Arsenic (As) 25,
Barium (Ba) 1000, Cadmium (Cd) 75, Chromium
(Cr) 60, Lead (Pb) 90, Mercury (Hg) 60, Selenium
(Se) 500]
Maximum allowable limit should not greater than
0.1 inches per second in horizontal burning
Shall meet the applicable requirements specified
by the actual product (see TP-09033-US)
Manufacturer or Distributor’s Name & Address
(City, State & Zip)
Product Description,
Net quantity of contents (U.S. and Metric units).
Country of Origin (19 CFR 134)
Country of origin should legibly, permanently
mark. Must be visible at time of purchase.
Phthalate –
BBP / DBP / DEHP, DNOP / DINP /
DIDP content
Soluble heavy metals
Flammability Requirement
Flammability of solids
(16 CFR 1500.44)
Flammability - California Technical
Bulletin 116 & 117
Labeling Requirement
Fair Packaging and Labeling Act
(FPLA) & Uniform Packaging and
Labeling Regulations (UPLR)
Responsible for updating: Jason Rao 1 of 4
Last change on: 10.02.2011 (dd/mm/yy)
Title:
TP – 09001 – US
01
Test Protocol
Version:
Report #:
Subject:
US report checklist - Children
Approved by: Stephan Pesch
Requirement
Shall be at least 0.00150 in (0.03810 mm) in
nominal thickness but the actual thickness shall
never be less than 0.00125 in (0.03175 mm) as
required based on length and perimeter criteria.
Alternatively, sheeting with an average thickness
of less than 0.00150 in. (0.03810 mm) shall be
Plastic Bag Warning
perforated with defined holes so that a minimum
of 1 % of the area has been removed over any
area of 1.18 x 1.18 in. (30 x 30 mm).
Otherwise, a warning label shall be printed on the
bag.
A permanent and distinguishing mark or code on
the product and its packaging, to the extent
practicable, allows the manufacturer and
purchaser to ascertain the name of the
manufacturer or private labeler, location and date
Tracking labels for children's of production of the product.
products
Verified the Presence only. The accuracy of
tracking label will not be verified.
Note: Manufacturer or Private Labeler name can
not be coded.
Applicable for:
full-size cribs and nonfull-size
cribs; toddler beds; high chairs, booster
chairs, and hook-on chairs; bath seats;
gates and other enclosures for confining
a child; play yards; stationary activity
centers; infant carriers; strollers;
walkers; swings; and bassinets and
Cradles; Children’s folding chairs, changing
tables, infant bouncers, infant bath tubs, bed rails
Requirements for Consumer
and infant slings.
Registration of Durable infant or
toddler products (16 CFR 1130)
On the product, it shall permanently marked with
the maunfacturer name, and contact information
(U.S. address and telephone number, toll free if
available); model name and number; date of
manufacture. (16 CFR 1130.4)
And a registration form/ card with complying the
content and the format per 16 CFR 1130.5-1130.7 shall be attached to the surface of each
durable infant or toddler product.
Law Label & Flammability Tag Requirement
Law Label & Flammability Tag Refer to the report if failure existed
Test Sample Result/Remark
Construction & Workmanship
Small Part (16 CFR 1501)
Items used by children under 36 months (3
years) of age shall not include removable,
liberated components, or fragments of toys
before and after use that are small enough
(without being compressed) to fit entirely within
the small parts cylinder
Items for children under 8 years of age shall not
have accessible, potentially hazardous sharp
edges before or after use.
Items for children under 8 years of age shall not
have accessible, potentially hazardous sharp
points before or after use.
Sharp Edge (16 CFR 1500.49)
Sharp Point (16 CFR 1500.48)
Responsible for updating: Jason Rao 2 of 4
Last change on: 10.02.2011 (dd/mm/yy)
Title:
TP – 09001 – US
01
Test Protocol
Version:
Report #:
Subject:
US report checklist - Children
Approved by: Stephan Pesch
Test Requirement
Shall have no components missing, malformed,
and/or fractured, no discernible surface
degradation including crazing, shivering, denting,
bubbles, cracks, stains, deformations, chips,
fractures, heavy lines, waves, shear marks,
scratches, scuff marks, indentations, or blisters.
The distance between two moving parts, during
the operation of folding or unfolding, are less
than 0.210 in (5.30 mm) or greater than 0.375 in
(9.50mm) (except at points where hinges, bolts,
rivets or other fixing devices are placed). If a
folding chair has arm rests, each component
ribbing, supporting member or protruding part of
the underside of the arm rests must be less than
0.210 in (5.30 mm) or greater than 0.375 in
(9.50mm) in radius. This test applies to pinching
or scissoring point where there are two moveable
components.
The hinge line between a stationary portion and a
movable portion of a sample must admit a 0.5 in
(13mm) diameter rod if it admits a 0.188 in
(5mm) diameter rod.
Furniture which has an accessible, circular hole
in any rigid material less than 0.062 in. (1.58 mm)
in thickness can admit a 1/4-in. (6-mm) diameter
rod to a depth of 3/8 in. (10 mm) or greater, it
shall also admit a 1/2-in. (13-mm) diameter rod.
The product shall be evaluated in all
manufacturer's recommended use positions.
Withstand 24 hours in 1% salt spray (fog) with no
major corrosion or visual change.
Mod. = modification of 1% salt spray
No change after 24 hours at 90% RH & 32° C
(90° F); report if entire item was placed in the
chamber or only certain pieces/sections. List
which pieces were tested, before and after
pictures of the pieces should be included.
For Indoor Use: Shall not exceed 12%
For Outdoor Use: Shall not exceed 15%
Place 25ml of distilled hot water on a horizontal
surface, wait 1 hour, wipe the spot clean and
examine for alterations in the surface including
discoloration, changes in gloss, blistering,
softening, swelling, loss in adhesion, or other
special phenomena.
Place 0.5ml of each stain on a horizontal surface,
cover with filter paper, wait 2 hours, dry, clean,
and examine for graying, spotting, wrinkling,
discoloration, or other film defects. Placement:
wine, ketchup, mustard, grape juice, cooking oil.
No objectionable stain by above list of household
chemicals after 2 hours.
Sample Result/Remark
Workmanship
Pinching or scissoring points -
folding chairs (ASTM F2613)
Hinge line clearance - folding
chairs (ASTM F2613)
Circular Holes in Rigid Materials
(ASTM F2613)
Environment Tests
Resistance To Corrosion (Metal
Components) (ASTM B117) (mod.)
Effects Of Humidity (ASTM D4332)
Moisture content - wood
components and MDF
Resistance to Hot Water
(ASTM D1308)
Stain Resistance
(ASTM D543 / ASTM D3023)
Responsible for updating: Jason Rao 3 of 4
Last change on: 10.02.2011 (dd/mm/yy)
Title:
TP – 09001 – US
01
Test Protocol
Version:
Report #:
Subject:
US report checklist - Children
Approved by: Stephan Pesch
Test
Effects of extreme temperature
change
Requirement
No failure or visual change after 24 hours at 0 ° F
and 120 ° F - report if entire item was placed in
the chamber or only certain pieces/sections. List
which pieces were tested, before and after
pictures of the pieces should be included.
Grade 4.0 @ 10 hours
Dry: Grade 4.0, Wet: Grade 3.0
Minimum Class 3.5
unit in “oz. / sq. Yd”
No major defects / two minor defects (Max.) &
Shall provide uniform color
Min. 50 lb
Abradant: H18, head wt: 500g,
200 cycles for leather, corduroy and vinyl only,
300 cycles for other fabrics,
Less than 10% weight loss
Min. 1.5 Lbs.
Min. 6 Lbs.
Sample Result/Remark
Colorfastness tests
Colorfastness to light (AATCC 16):
Colorfastness to (rotary) crocking
(AATCC 8/116):
Colorfastness to Water Spotting
(AATCC 104):
Textile characteristics
Fabric weight (ASTM D3776):
Fabric defects & Evenness of color
(ASTM D3990):
Fabric strength – length & width
(ASTM D5034):
Abrasion resistance
(ASTM D3884):
Tear strength - for leather – fill &
wrap (ASTM D4704):
Tear strength - for most fabrics
except leather - fill & wrap
(ASTM D1424):
Instruction & Assembly Instruction
Use/care instructions
Shall be clear, understandable, accurate, legible,
free from grammar and spelling errors, shall be
provided in language appropriate to destination
countries.
Shall be accurate & easy to follow. Assembly can
not shear screw heads, break screws or cause
other problems. Assembly time need to be noted.
Assembly Instruction
Overall result:
passed failed Signature:………………………………
The decision about which tests need to be conducted is made by the person in charge (see header).
Additional remarks should be added on the back page!
Responsible for updating: Jason Rao 4 of 4
Last change on: 10.02.2011 (dd/mm/yy)
更多推荐
要求,家具,强度,儿童,包括,美国,防火
发布评论